Brand Logo
Magazine-style header for USG technical article

Technical article

I Almost Saved My Client $1,800 on a Bathroom Renovation—And It Would Have Cost Them $4,200

by Celeste Fournier

The Quote That Looked Too Good

In Q1 2025, I was managing procurement for a boutique fitness studio renovation—a 24,000-square-foot build-out our client had budgeted at $250,000 for the full project. My slice was the three bathrooms. Not glamorous, but I controlled about $18,000 of that budget for fixtures, doors, and finishes.

I'd been tracking every invoice in our cost system for six years at that point. Managed roughly $180,000 annually across vendors. So when two quotes came in—one from a Kohler authorized dealer at $12,400 and one from a regional supplier at $10,600—my first instinct was to flag the $1,800 gap and push the Kohler dealer to match. Classic cost-controller move, right?

That's what I thought. Then I did the math.

The Fine Print That Almost Got Me

Here's what the $10,600 quote included: no-name shower and tub doors with a 1-year warranty, a generic roman tub faucet that wasn't compatible with the rough-in valve our plumber had already installed (learning moment), and—get this—door hinges that were listed as "standard duty, suitable for residential use." This was a commercial gym. With steam rooms.

I asked the regional supplier about the hinges. Their rep said, "Oh, they'll be fine for light commercial." I asked what "light commercial" meant. He said, "You know, offices and stuff."

That was my first red flag. But honestly? I was on the fence. The client's budget was tight, and $1,800 is $1,800. I remember thinking, We've worked with this supplier before. They delivered on time for the last three orders. What are the odds the hinges fail?

Well, the odds caught up with me.

The $4,200 Phone Call

We went with the cheaper quote—no, wait, I should correct that. We almost went with it. The day before I signed the PO, I got a call from the plumber. He'd done a site walk and noticed the shower and tub door specs didn't match the opening dimensions we'd framed. The cheap supplier had quoted a "standard 60-inch" unit, but our openings were 58.5 inches because of a load-bearing wall the architect refused to modify.

Standard units don't trim down. Custom sizing meant a 6-week lead time and an extra $1,900 in fabrication. Oh, and the roman tub faucet? Wrong rough-in. That was another $850 for a new valve and $450 for re-tiling around the access panel. Plus the hinges we'd need to replace within 18 months because "residential duty" doesn't hold up to daily steam exposure—I got a quote on commercial-grade replacements: $1,200 installed.

Total hidden cost of the "cheaper" quote: $4,400. More than double the initial savings.

That's when I called the Kohler dealer back. Their quote had included custom-sized shower and tub doors, a roman tub faucet matched to our existing rough-in, and commercial-grade door hinges rated for high-traffic use. All included. No surprises. The $12,400 wasn't cheap—it was complete.

What Actually Bothers Me About That Whole Mess

Here's the part I can't let go of: the regional supplier knew we were a small project. They knew the order was under $15,000. And I'm convinced part of the reason they quoted "standard residential" hinges is that they didn't think we'd notice. Small order, small client—why invest in getting the details right?

I've been on both sides of that dynamic. When I was starting out in procurement, I had vendors flat-out tell me my $1,200 order wasn't worth their time. One supplier actually said, "We usually have a $5,000 minimum for commercial projects." The vendors who treated my small orders seriously? Those are the ones I still call for $50,000 contracts.

So when the Kohler dealer sent a rep out to re-measure the openings himself—no extra charge, just to make sure the custom dimensions were right—I noticed. That's not a brand tax. That's a vendor who knows the value of getting the next order, and the one after that.

The Numbers That Actually Matter

After the project wrapped, I ran the final numbers. Total bathroom fixture spend: $13,700. That included the Kohler shower and tub doors, the roman tub faucet assembly, and all the replacement hardware. Our original budget was $18,000. We came in under—not because we found the cheapest line-item bid, but because we stopped optimizing for unit price and started optimizing for total installed cost.

For context on scale: the entire build-out landed at $248,200 (based on our Q1 2025 final invoice; construction costs vary by region and scope—verify current rates locally). The bathroom was less than 6% of that. But it was the 6% that almost became a cautionary tale.

The boutique gym owner—who'd never built anything before—told me later that she'd Googled "how much does it cost to build a house" before we started, just to get a ballpark. She said the numbers ranged from $150,000 to $400,000 and she had no idea what applied to her. I told her the truth: those ranges are useless without scope. A $150,000 house in rural Tennessee isn't the same product as a $400,000 house in Seattle. What matters is who's quoting you and what they're including.

Which, honestly, is the same lesson I learned with the hinges.

What I Do Differently Now

Three things changed in my procurement process after this project.

First: I ask every vendor to itemize what's not included. Not as a gotcha, but as a standard question. The Kohler dealer's quote had a line at the bottom: "Pricing includes custom sizing, commercial-duty hardware, and finish matching. Not included: rough-in valve modifications." The cheap supplier's quote said nothing about exclusions. That silence cost me almost $4,400.

Second: I stopped assuming "same specs" means identical products. I assumed standard shower and tub door specs meant universal fit. Didn't verify. Turned out "standard" means something different to every manufacturer and every framing crew. Learned never to assume dimensions match just because the spec sheet lines up on paper.

Third: I pay attention to how vendors treat small orders. The Kohler rep did a site visit for a $12,400 job. He didn't have to. But that's exactly why his quote was the right call. If someone won't invest two hours on a small project, they're not going to invest two weeks when something goes wrong on a big one.

I still have that regional supplier's number saved. I just don't call it. The bottom line is simple: cost control isn't about finding the lowest number on the page. It's about finding the number that doesn't change after you've signed the contract.

To be fair, the cheaper quote did save us about $200 in the short term—the delivery was three days faster. But that three days bought us a six-week custom fabrication delay. So, you know, not exactly a win.

Celeste Fournier

Celeste Fournier

Celeste Fournier is an interior building-products analyst covering wall panels, gypsum board, acoustic ceilings, decorative moulding, wallpaper systems, architectural coatings, sealants, and finishing accessories. She applies ASTM C423 sound-absorption results and ASTM E84 surface-burning data while assessing NRC, flame-spread index, smoke-developed index, dry-film thickness, adhesion, joint movement, cleanability, and finish consistency. Her technical articles help designers, contractors, and facility teams coordinate appearance, acoustics, fire-performance documentation, application conditions, and long-term maintenance.

Previous Moen Replacement Parts vs. Full Fixture Swaps: A B2B Comparison Guide Next Tile Refinishing vs. Full Replacement in East Florida: A Cost Controller's Honest Math

Recent articles